Materials (Film/Paper/Tape)

Tensile Strength Test of Plastic Bag Handle

To determine the tensile strength of plastic bag handle, grip a plastic bag handle with dedicated grips, and pull it to break with a force gauge. IMADA offers the dedicated testing system such as the following configuration, which is utilized in quality control and R&D.
Click here
for Details

Coefficient of Friction Measurement for Papers (Complies with the corresponding part of JIS P8147: 2010)

To determine coefficient of friction (COF) of paper, pull the weight with sample to slide it against the sample on the table, then calculate the COF by the supplied software. It complies with the corresponding part of JIS P8147: 2010. IMADA offers the dedicated testing system such as the following configuration, which is widely used in quality control and R&D.
Click here
for Details

Crimped Postcard Peel Strength Test

This is peel strength test of crimped postcard. IMADA offers the dedicated testing system such as the following configuration, which is utilized in quality control and R&D.
Click here
for Details

Tension Strength Test of Packaging film

To determine the tensile strength of packaging film, grip a film specimen with 2 pcs of dedicated grips, and pull the specimen with a force gauge. IMADA offers the dedicated testing system such as the following configuration, which is widely used in quality control and R&D.
Click here
for Details

180-Degree peel test (adhesion test) of adhesive sheet by using peeling tester

This is 180-Degree peel test (adhesion test) of adhesive sheet by using peeling tester. It is for quality control and R&D. It enables testings compling with the corresponding part of ISO and JIS standards.
Click here
for Details

Breaking strength test of embossed carrier tape

Embossed carrier tape’s covering film is pulled to measure its breaking strength for quality control. It enables testing according to the correspondling part of IEC and JIS standard.
Click here
for Details

Pharmaceutical packaging push out test

Pharmaceutical tablet is pushed out from packaging to measure the packaing functionality for quality control and R&D.
Click here
for Details

Adhesive tape peel strength test (Force-Displacement)

Adhesive tape is pulled to measure its peel strength for quality control and R&D. It enables testing according to the correspondling part of JIS standard.
Click here
for Details

Packaging film coefficient of friction test

This coefficient of friction (COF) test is performed to measure sliding friction of packaging film for quality control and R&D. It enables testing according to the correspondling part of JIS standard.
Click here
for Details

Materials (Corrugated Cardboard/PP band/Cushioning Material)

Buffer material hardness test

This test is to measure buffer material hardness (elasticity/cushioning characteristics) for quality control.
Click here
for Details

Corrugated cardboard durability test

Corrugated cardboard is pressed to measure its durability for quality control and R&D.
Click here
for Details

Tension Strength Test of Polypropylene Strapping Band

Polypropylene Strapping Band is pulled to measure its tension strength for quality control. It enables testing according to the correspondling part of JIS standard.
Click here
for Details

Food Packaging

Retort Pouch Durability (Burst Strength) Test (Complies with the corresponding part of JIS Z0238:1998)

To determine the durability (burst strength) of heat-sealed packages such as retort pouches, keep a package pressed at a constant force with a force gauge and a dedicated fixture. IMADA offers the dedicated testing system such as the following configuration to comply with JIS, which is utilized in quality control.
Click here
for Details

Film Puncture Strength Test

To determine the puncture strength of packaging film, stick film through with the dedicated pin combined with a force gauge. IMADA offers the dedicated testing system such as the following configuration to comply with JIS, which is widely used in characteristic evaluation, quality control, and R&D.
Click here
for Details

Peel test of jelly container lid (manual test)

Film lid of jelly container is peeled by hand to test the peel strength simply. It is for quality control.
Click here
for Details

Unsealing test of jelly container lid

Film lid of jelly container is peeled by IMADA 45 degree peel test fixture to keep 45 degree during test to test the peel strength. It is for quality control.
Click here
for Details

Heat seal strength test

This test is to measure heat seal strength (peel strength) of food packaging for quality control and R&D.It enables testing according to the correspondling part of JIS standard.
Click here
for Details

Packaging film opening (tearing) strength test

This test is performed to measure force to open (tear) packaging film for quality control and R&D.
Click here
for Details

Beverage Packaging

Puncture Test of Paper Straw

This is puncture test of paper straw. Stick the paper straw into the film lid and test the maximum force. IMADA offers the dedicated testing system such as the following configuration, which is utilized in quality control and R&D.
Click here
for Details

3-Point Bending Test of Paper Straw

This is 3-point bending test of paper straw to evaluate its bending strength. By using IMADA graphing software, the testing results of different material and diameter, or samples in different soaking time can be compared in one screen. IMADA offers the dedicated testing system such as the following configuration, which is utilized in quality control and R&D.
Click here
for Details

Screw Cap Torque Test of Bottles

To determine the opening/closing force of a bottle's screw cap, fix the specimen by IMADA screw cap torque tester and rotate the specimen by hand. IMADA offers the dedicated torque testing system such as the following configuration, which is widely used in quality control and R&D.
Click here
for Details

Stay-On-Tab Package (Beverage Can) Opening Test Complies with the corresponding part of ISO 17480: 2015

This is opening test of stay-on-tab package (beverage can) in conformance with the corresponding part of ISO 17480: 2015. IMADA offers the dedicated testing system such as the following configuration, which is utilized in quality control and R&D.
Click here
for Details

500ml Plastic Bottle Top-load Testing

This is plastic bottle top-load testing for characteristic evaluation, and quality control.
Click here
for Details

Pharmaceutical Packaging

Screw Cap Torque Test of Bottles

To determine the opening/closing force of a bottle's screw cap, fix the specimen by IMADA screw cap torque tester and rotate the specimen by hand. IMADA offers the dedicated torque testing system such as the following configuration, which is widely used in quality control and R&D.
Click here
for Details

Opening torque test of large bottle

This is opening torque test of large bottle from pharmaceutical or food industry by using TAA series for torque-time or torque-angle analysis. It is for quality control and R&D.
Click here
for Details

Compression test of push bottles

This is compression test of push bottles such as disinfectant spray, cosmetics push bottle. It is for quality evaluation and quality control.
Click here
for Details

Packaging Container

Spray press button compression test

This is spray press button compression test for quality control and R&D.
Click here
for Details

Spray Bottle Cap Insertion-Extraction Test

Lid (cap) of cosmetic container is extracted/inserted repatitively to measure the durability quality control and R&D.
Click here
for Details